|
Section#201 |
Part # |
Description |
|
|
04054 |
GLENDINNING
CABLEMASTER GUIDE ROLLER ASSEMBLY |
|
|
Used to replace the Guide Roller/Out-Limit Assembly which is
relocated at the end of the pipe when the vertical pipe extension is
used.
|
| Order
switches separately |
|
Material: Anodized Case Aluminum, Stainless Steel Pins, Nylon Rollers
|
|
|
|
| Section#202 |
Part # |
Description |
|
|
04069 |
GLENDINNING
CABLEMASTER UNDER COACH ROLLER ASSEMBLY |
|
|
Typically used in RV applications
|
| Used to keep cable from chafing on sharp edges |
| Material: Anodized Aluminum, Stainless Steel Pins, Nylon Rollers |
|
|
|
| Section#203 |
Part # |
Description |
|
|
XXXXX |
GLENDINNING
CABLEMASTER ANGLING ASSEMBLIES |
04062
04064
04066
04063
04067
04065
|
30 degree Angling Assembly
60 degree Angling Assembly
90 degree Angling Assembly
120 degree Angling Assembly
150 degree Angling Assembly
180 degree Angling Assembly
|
| Used to direct the cable from 30 - 180 degree bends.
|
| Uses Guide Roller Assemblies mounted on a flat aluminum plate to
direct the cable. |
| Note: (2) Pipe Extension Plates (#50004) are needed to attach angling
assembly to accessory items. |
|
|
|
| Section#204 |
Part # |
Description |
|
|
04070 |
GLENDINNING
CABLEMASTER LOW PROFILE BRACKET ASSEMBLY |
|
|
Used to lower the height required to mount the Cablemaster from 12
1/2" to 10"
|
| Motor wire leads are to be reverse when using this assembly. |
|
|
|
| Section#205 |
Part # |
Description |
|
|
XXXXX |
GLENDINNING
CABLEMASTER PIPE ELBOW
/ ROLLERS |
04059
04060
|
22-1/2 degrees
45 degrees
|
| Typically used in RV applications,
to direct the cable in a 22 1/2 or 45 degree bend |
| Fits 3" schd 40 PVC Pipe |
|
|
|
| Section#206 |
Part # |
Description |
|
85423 |
GLENDINNING CABLEMASTER 2" - 3" COUPLING ADAPTER
|
| |
Used to reduce pipe size from 3" to 2".
|
| |
|
|
|
| Section#207 |
Part # |
Description |
|
|
04057 |
GLENDINNING
CABLEMASTER 2 - 3" COUPLING ADAPTER w/SEAL |
|
|
Same as above with neoprene seal to wipe cable.
|
|
NOTE: Pipe End Roller ASSY. (#04040) can be glued here if there is a
bend directly after coupling to avoid binding.
|
|
|
|
| Section#208 |
Part # |
Description |
|
|
04045 |
GLENDINNING
CABLEMASTER PIPE TO PIPE ANGLING ASSEMBLY |
|
|
Used with the Vert. Pipe Ext. and the Horz. Pipe Ext. for angling
3" PVC pipe to a desired angle.
|
| Components included:
2 - 04040 Pipe End Roller Assembly |
|
2 - 04052 Pipe clamp Assembly (single) |
|
1 - 50005 Connector link |
|
|
|
| Section#209 |
Part # |
Description |
|
|
50408 |
GLENDINNING
CABLEMASTER POWER UNIT TO CONTAINER MOUNTING BRACKET - 17" High |
|
|
Used to mount Power Unit to the container for easy Cablemaster
installation.
|
| Mounting Bracket can be attached to all containers we
sell. |
| Note: Overhead Mounting bracket (#50006) is required in order to
mount the Power Unit to these brackets |
|
|
|
|
Section#210 |
Part # |
Description |
|
|
50407 |
GLENDINNING
CABLEMASTER POWER UNIT TO CONTAINER MOUNTING BRACKET
- 12" High |
|
|
Same as above.
|
|
Note: Overhead Mounting bracket (#50006) is required in order to
mount the Power Unit to these brackets
|
|
|
|
| Section#211 |
Part # |
Description |
|
|
04068 |
GLENDINNING
CABLEMASTER CABLE DIVERTER ASSEMBLY |
|
|
Typically used in RV Applications used when cable needs to be diverted downward directly in front of
the Power Unit.
|
| Note: Existing connector link used to attach cable diverter to unit.
Existing Out-Limit/Guide Roller Assembly mounted here. |
|
|
|
| Section#212 |
Part # |
Description |
|
|
50413 |
GLENDINNING
CABLEMASTER MOUNTING BEZEL |
|
|
Used when the Hawse Pipe Cap and Hinge should not protrude from
the side or exterior of the mounting surface.
|
| Material: Anodized Cast Aluminum, Painted Gloss White |
|
|
|
|
NEXT
PAGE
|
|
|
|
|
|
|
|
Revised:12/22/2006 09:48:31
|